If you have an MSI motherboard with a SATA port that isn’t working, it’s likely because the SATA port is disabled in the BIOS. To enable the SATA port, you’ll need to access the BIOS and change the configuration. This can be done by pressing a key during bootup, such as F2 or DEL.
Once in the BIOS, look for a setting called “SATA Configuration” or “Onboard Devices.” Enable the SATA port and save your changes. You may need to consult your motherboard manual for specific instructions on how to do this.
Fix New Hard disk Drive or SSD not detected on MSI Mainboard
- Enter the BIOS setup utility by pressing the “Delete” key during system startup
- The MSI logo will appear on-screen during bootup; keep tapping the “Delete” key until the BIOS menu appears
- Use the arrow keys to navigate to the “Integrated Peripherals” menu
- This is typically located near the bottom of the BIOS menu
- Use the arrow keys to scroll down to “SATA Controller Mode
- ” This option may also be listed as “SATA Mode,” “SATA Configuration,” or something similar
- Press the “Enter” key to select this option, then use the arrow keys to change its value from “IDE” to either “AHCI” or “RAID
- ” If your SATA controller mode is already set to AHCI or RAID, you do not need to change it
- Press F10 then Enter when prompted in order confirm and save your changes, then reboot your computer for the changes take effect
Credit: www.anandtech.com
How Do I Enable Sata Port in Bios Msi
If you have an MSI motherboard with a Serial ATA (SATA) port, you can enable it in the BIOS to use SATA devices. To do this, follow these steps:
1. Reboot your computer and press the F2 key when the MSI logo appears.
This will take you into the BIOS setup utility.
2. Use the arrow keys to navigate to the Advanced tab.
3. Select Integrated Peripherals from the menu on the left side of the screen.
4. On the right side of the screen, find SATA Mode and change it from IDE to AHCI or RAID, depending on your needs.
5 Press F10 to save your changes and reboot your computer.
Enter the Bios Menu, Then Look for the Storage Configuration Option
If you’re not sure how to enter the BIOS menu, check your computer’s manual or look for a “Boot Options” or “BIOS Menu” selection during startup. Once you’ve entered the BIOS menu, find the Storage Configuration option. This will likely be under a “Boot Order” or “Advanced” section.
From here, you can change the boot order of your drives so that your computer boots from a USB drive first. Save your changes and exit the BIOS menu to boot from your USB drive.
2
How can social media help small businesses
Social media has become an integral part of many people’s lives and it is also becoming increasingly important for businesses. Small businesses can benefit from using social media in a number of ways.
One way that social media can help small businesses is by providing a low-cost way to market their products or services. Traditional marketing methods, such as print or television advertising, can be quite expensive, especially for small businesses with limited budgets. Social media provides an affordable way to reach out to potential customers and promote your business.
Another benefit of using social media for small businesses is that it allows you to build relationships with your customers and create a community around your brand. Customers are more likely to buy from companies that they feel connected to and engaged with. By interacting with customers on social media, you can create loyalty and goodwill towards your business.
Finally, social media can be used as a tool to gather feedback from customers about your products or services. This feedback can be valuable in helping you improve your offerings and make your business more successful.
Select the Sata Controller Mode Option And Change It to Ahci from Ide
SATA (Serial ATA) is a computer bus interface that connects host bus adapters to mass storage devices such as hard drives and optical drives. SATA uses a point-to-point architecture, meaning each device is connected directly to the host controller with no sharing of bandwidth between devices. This allows for much higher data transfer rates than earlier parallel SCSI buses.
The most common mode of operation for SATA controllers is IDE Compatibility mode, also known as Legacy mode. In this mode, the controller appears to the operating system as an IDE controller, allowing it to work with older software and drivers that do not support SATA natively. However, this compatibility comes at the expense of performance, as the controller must emulate the older Parallel ATA protocol.
To get the best performance out of your SATA controller, you should change it to AHCI (Advanced Host Controller Interface) mode. AHCI was designed specifically for Serial ATA controllers and offers several advantages over IDE Compatibility mode:
* Native Command Queuing: This allows the drive to reorder commands to optimize seek time and rotational latency.
This can result in significant performance gains on modern hard drives.
* Hot Plugging Support: Allows you to hot plug or unplug SATA devices without rebooting Windows. This can be very useful if you need to add or remove a drive frequently (e.g., for backups).
* Port Multiplier Support: Allows multiple drives to be daisy chained from a single port on the motherboard or host controller card.
3
How does the immune system work?
The human body is made up of trillions of cells, each with its own specific function. One type of cell, called a macrophage, acts as a “scavenger” and engulfs foreign material, such as bacteria and viruses.
The macrophage then displays bits of the foreign material on its surface. These displayed bits are recognized by other specialized cells, called T-cells. The T-cell produces special chemicals that destroy the foreign invader.
B-cells are another type of cell that also recognizes foreign material. When a B-cell encounters a virus or other invader, it produces antibodies – proteins that attach to the invader and neutralize it.
Press F10 to Save Your Changes And Reboot the Computer
Assuming you would like a blog post on how to use the F10 key to save changes and reboot a computer:
The F10 key is a function key on many computers. It is typically used to save changes before exiting or restarting a program or shutting down the computer.
In some programs, pressing F10 may also bring up a menu of options.
To save your changes and reboot the computer using the F10 key, first make sure you have made all the desired changes in the program or settings you are currently in. Once you are ready to save and exit, look for the ‘Save’ or ‘Save & Exit’ option in the File menu at the top of the screen.
If there is no such option, press Alt + F4 to bring up a dialog box asking if you want to save your changes before exiting; select ‘Yes’ and press Enter. With either method, once you have saved your changes, press F10 to reboot your computer.
Conclusion
If you have an MSI motherboard with a SATA port that isn’t working, you may need to enable it in the BIOS. To do this, follow these steps:
1. Enter the BIOS by pressing F2 during bootup.
2. Go to the Advanced tab and select Integrated Peripherals.
3. Find the SATA port that you want to enable and select Enabled from the drop-down menu next to it.
4. Press F10 to save your changes and exit the BIOS.
Your SATA port should now be working properly.