How to Remove Rubber Boot Novo 2

To remove the rubber boot from the Novo 2, first pull back on the heel tab. Next, use your thumb to press down on the top of the boot while pulling up with your other hand. The boot should come off easily.

If it is difficult to remove, you can try using a shoehorn or a butter knife to help pry it off.

  • Unscrew the four screws that hold the boot in place
  • Carefully lift the boot off of the machine
  • Use a damp cloth to clean any residue off of the machine
  • Place the boot back on and screw it in place

Smok Novo 3 Pin Stuck down

If you’ve been using your Smok Novo 3 for a while, you may have noticed that the pin has become stuck down. This can be frustrating, especially if you’re trying to use the device with another mod or atomizer. Fortunately, there are a few things you can do to fix this problem.

First, make sure that the contact point on the bottom of the device is clean. If it’s dirty, wipe it off with a cotton swab or cloth. Next, check the 510 connection to see if it’s loose.

If it is, tighten it up with a Phillips head screwdriver. If neither of these solutions works, then your best bet is to contact Smok customer service. They should be able to help you troubleshoot the problem and get your device working properly again.

How Do You Take Apart a Smok Novo 2 Pod?

Assuming you want to know how to take the pod out of the device: To remove the pod, first unscrew the base of the pod (the part that screws into the device) and then pull the pod out. The coil is located at the bottom of the pod and is held in place by a small metal tab.

To remove the coil, simply pull it out from the bottom of the pod.

How Do You Fix a Novo 2 If It Won’T Hit?

If your Novo 2 won’t hit, there are a few things you can try to fix it. First, make sure that the battery is fully charged. If the battery is low, it may not have enough power to heat the atomizer coil properly.

You can also try priming the coil by running it under hot water for a few seconds. This will help loosen any gunk that may be stuck on the coil. Finally, if all else fails, you can try replacing the atomizer coil altogether.

Why Does My Novo 2 Leak So Much?

If you’re using a Novo 2 and noticing that it’s leaking more than usual, there are a few possible reasons why. First, check to make sure the coil is screwed in securely. If it’s loose, tighten it up and see if that stops the leak.

If the coil is tight and the leak persists, try replacing the coil with a new one. Another possibility is that the tank itself is cracked or damaged. Inspect the tank for any visible cracks or damage and replace it if necessary.

Finally, make sure that the O-rings (rubber seals) are in good condition and not dried out or cracked. If they are, replace them with new ones. If you’ve tried all of these things and your Novo 2 continues to leak, bring it to your local vape shop or contact Eleaf customer service for further assistance.

How Do You Fix a Novo 2 Leak?

If your Novo 2 is leaking, there are a few things you can do to try and fix the issue. First, make sure that the tank is properly screwed on. If it is not, screw it on until it is tight.

If the tank is screwed on correctly and the leak persists, check to see if the O-ring seal at the base of the tank is intact. If it is damaged or missing, replacing it should fix the leak. Finally, if neither of these solutions works, you may need to replace the entire tank.


If your Novo 2 has a rubber boot and you want to remove it, here’s how. First, find the small hole in the center of the boot. Next, insert a paperclip or other small object into the hole and twist to unlock the boot.

Finally, pull the boot off of your device. If you have any trouble removing the boot, contact customer support for assistance.






Leave a Reply

Your email address will not be published. Required fields are marked *